Friday, September 26, 2008

Heat Exchanger Safety - A Maintained Furnace is a Safe Furnace

Heat exchangers are pieces of equipment that are used for the transfer of heat from one fluid to another. When a heat exchanger goes bad, chances are, important things stop working. When your automobile engine is overheating, it's likely that the heat exchanger is the problem. You probably call it a radiator, but it's one type of heat exchanger. In your radiator, antifreeze cools air that flows past it. This air is then blown by a fan onto the engine to keep it cool. If the radiator doesn't work properly, you won't be driving very far until the situation is fixed.

Your home heating system also has a heat exchanger. In fact, nearly every piece of mechanical equipment that has a need to intentionally heat or cool part of a system does. Inside your furnace there is a combustion chamber. There is a metal wall that separates the internal combustion from the air that flows past the heat exchanger and on through the ductwork to heat your home. You need this separation because you don't want the toxic gases inside mixing with the air that is distributed throughout your home. In the previous example, a faulty heat exchanger could lead to a broken down automobile, but in your home you could be gambling with your life.

Carbon Monoxide can be present in the combustion gases. It's supposed to be contained inside, but as time goes on, it becomes possible for the heat exchanger in your furnace to crack or warp. Each time your furnace turns on, the metal wall heats up and expands. During the off cycles, the metal of the heat exchanger cools and contracts. Over time this repeated process of expansion and contraction of the metal takes it's toll. The metal can become fatigued, and eventually warp out of shape, or just plain break.

As I noted before, these metal walls were designed to keep the toxic combustion gases inside the heat exchanger chamber. Guess what happens if there is a crack? That's right, the toxic gases inside can mix with the forced air that is being blown through the ductwork and into your home. Having a reliable Carbon Monoxide detector is an inexpensive measure to protect yourself and your family from the danger of Carbon Monoxide poisoning, but you can also take some proactive measures to protect against any potential danger.

Give your furnace an annual checkup, just before the heating season, to check the condition of the burners, the heat exchanger, the furnace filter, and other components that can affect the performance of your furnace. I recommend have a certified HVAC specialist do this. Only a certified specialist will have the knowledge and experience needed to know exactly what to look for, and where to look for it, as well as knowing what the operating specifications for your unit should be.

If your furnace is over 10 years old, it is even more important to keep that annual checkup. This is the time period where the years of wear and tear on your heat exchanger make a failure of the heat exchanger wall significantly more likely. Keeping your furnace in good health can also help keep you and your family in good health.

Find out more about heat exchanger safety at my heat exchanger cleaning equipment site.

Saturday, September 6, 2008

Filtration Systems Can Reduce Maintenance and Downtime.

To strike an interesting analogy, your cooling tower and heat exchanger is what the lungs and heart are to the human body; when either aren't working properly, it effects other parts of the body and your health suffers. Similarly, when your cooling tower and heat exchanger isn't clean, the heat exchange process doesn't work efficiently and the health of your production and process cooling system suffers.

Process cooling systems that rely on cooling towers to dissipate heat from process cooling water accomplish this by drawing massive volumes of air into the cooling tower as the water travels through the fill material on its way back to the basin. Through the natural evaporative process, heat is dissipated from the water before it reaches the water basin from which it is re-circulated through the chiller then through the heat exchanger and back again (kind of like when you sweat while working and letting the air evaporate the perspiration to cool you down). It is important to realize that cooling towers are gigantic air scrubbers that capture all airborne debris that happen to be floating nearby, and if your system doesn't have effective filtration, the debris can clog the fill and get circulated and trapped in the heat exchanger where it can build-up, restrict water flow and cause your process equipment to malfunction due to overheating.

An example of this is illustrated by a major automotive assembly facility that had faced periodic downtime due to their robotic welding systems not holding tolerances and causing quality problems. After the robotic technicians spent several days trying to initially solve the problem, one of the maintenance workers opened the heat exchanger and discovered that it was impacted with cottonwood seed, insects and other debris - flow had been reduced and the robotic equipment was running hot. Now you might be asking yourself, whey didn't they have some sort of filtration equipment? The answer is simple; at the time the facility was built, the ambient conditions in that area didn't require a filtration system. However, as the years went by and the area became more developed and cottonwood tree populations grew, the need eventually surfaced.

The interesting thing to note about this situation is that even though cleaning the heat exchanger got the robotic welding system back on-line and running at peak performance, it didn't solve the problem. In fact, cleaning heat exchangers is like taking a cold capsule to relieve the symptoms of a cold. Unless you treat the root cause of the problem, the cooling system will suffer time and again. The root cause in this case and in most heat exchanger fouling situations is the cooling tower - stop the debris from getting into the cooling tower and it will protect the entire process cooling system including fill, cooling water, chiller and heat exchanger. With the proper filtration technology, your process cooling system will stay clean and running efficiently all season long.

Selecting The Right Filtration System

It is important to realize that optimizing the ecology and operational efficiency of your evaporative cooling system is best accomplished by combining a chemical treatment regimen with some type of filtration. The reason is that chemical treatment specifically targets suspended solids and particulates of 40 microns and below, while filtration systems are designed to stop larger debris, especially the kind that causes system clogging and fouling.

For cooling tower filtration, there are two general technologies: Water Based Systems for which there are a few different variations and Air Intake Filtration Systems. With water-based systems, the choices include basic water strainers that remove debris by simply passing water through a mesh strainer; sand filtration systems that remove debris by passing the water through sand and centrifugal separators that spin the water and remove the debris through centrifugal action. In contrast, Air Intake Filter Systems remove the debris by filtering the air as it is being drawn into the cooling tower, keeping the debris out of the system in the first place. When considering your filtration options, the following questions should be asked.

  • What is the cost associated with downtime due to heat exchanger or cooling tower fouling or clogging? (Knowing this will help you justify your filtration system cost)
  • What type of debris is most problematic (can you see it or is it microscopic)?
  • Specifically what part of the system does the filter protect?
  • Which system provides the greatest filtration surface area (this can directly impact frequency of cleaning - the smaller the filter the more frequently it needs cleaning)
  • Can the system be installed without shutting down the cooling tower? (If the cooling tower must be shut down for installation, you need to factor lost productivity into the cost of your filtration system if it's not being installed during shutdown periods.)
  • What is the cost associated with both the filter and installation?
  • How easy is the system to install and maintain?
Answering the above questions will help you to fully understand your options and to make the best choice for your operation.

In the case of the automotive manufacturer, the solution they selected was the Air Intake Filter system. The reason was that they needed a system that would protect their entire process cooling system including fill material, cooling water, chiller and heat exchanger. When they evaluated water-based systems, they discovered that the options provided varying degrees of protection for the chiller and heat exchanger but didn't protect the cooling tower where the root of their problem was. If they had selected a water-based system, their cooling tower would have still drawn airborne debris into both the fill and water where the water filter would have captured the debris before it circulated throughout the system. From a maintenance standpoint, that would have solved the heat exchanger problem but it would have done little to reduce maintenance on the cooling tower. Further, when they compared the cost of water based filtration versus air intake filtration technologies, Air Intake Filtration was found to be the more cost effective approach for their operation.

If you are not currently using a filtration system as part of your process cooling system, then any filtration technology will give you more protection than you have now, however, selecting a solution best suited to your operation requires that you know what kind of debris is the problem and where it is getting into the system. As a rule of thumb, " don't select a small debris solution to solve a large debris problem". Conversely, "don't select a large debris solution to solve a small debris problem". There is clearly a place for both water based filtration and air intake filtration - be sure you're selecting the right filtration for your specific need.

If you are looking to protect only your chiller and heat exchanger from airborne debris, then one of the water-based filtration technologies in combination with a good water treatment program can help you manage the debris that gets into the cooling water. If on the other hand, you're looking for full process cooling system protection, then you should look at Air Intake Filtration - It will stop the debris from getting into your system in the first place.

Air Solution Company developed and patented the first Air Intake Filter specifically engineered to mount to the outside of cooling towers and other HVAC equipment for purposes of stopping the debris before it entered into the system. Since that time, Air Solution Company has been manufacturing and has introduced a variety of other innovative filter systems including its new Fine Mesh Filter which is engineered for use on small and medium size refrigeration coils and machine fan intake housing units. Air Solution Company Randy Simmons is with Air Solution Company, author of articles can be reached at http://www.airsolutioncompany.com